Once programmed, navigating the RC-799M requires understanding its primary zones.

Turns the Onkyo AV receiver on or puts it into standby mode.

Even with a simple device like the RC-799M, problems can occasionally arise. Here are some of the most common issues and how to solve them.

If the code is accepted, the indicator light will flash twice and turn off. If it flashes once slowly, the code was incorrect, and you must restart from Step 3.

The Onkyo RC-799M is a relatively simple device, but proper understanding is essential to fully utilize your AV receiver. Many users seek out the manual for various scenarios:

The RC-799M is a learning remote, meaning it can control your Samsung TV or Sony Blu-ray player. You do not need the original remote for the other device.

Click the battery cover securely back into place.

The RC-799M features a logical, zone-based button layout designed to control both your main AV receiver and connected source devices. 1. Power and Input Selection

| | Likely Cause | Solution | | :--- | :--- | :--- | | The remote does not work at all | Dead batteries | Replace the two AA batteries with fresh ones. | | | Obstruction | Ensure nothing is blocking the IR sensor on the receiver front panel. | | | Wrong polarity | Check that the + and – symbols align with the markings in the battery compartment. | | Some buttons work, but others don't | Dirt/Debris | The remote may have liquid or debris trapped under the buttons. Gently clean the exterior with a soft, dry cloth. | | | Generic limitation | If this is a replacement remote, it may not support the "Mute" button or secondary device control. Check your product listing for limitations. | | Short range (must be very close to the receiver) | Low batteries | Weak batteries reduce the infrared output. Replace them immediately. | | | IR sensor wear | Over time, the IR emitter can weaken. Try a different angle. |

Hold down the DISPLAY button and the appropriate REMOTE MODE button (e.g., TV, BD/DVD, or CBL/SAT) simultaneously for roughly 3 seconds. The remote's indicator light will light up or blink.

Make sure no physical objects are blocking the path between the remote and the receiver.

: Compact fluorescent lamps (CFLs) or bright sunlight hitting the receiver’s front display can interfere with infrared signals. Try shielding the receiver from direct light. 6. Compatible Onkyo Receiver Models

Hold both buttons for approximately 3 seconds until the remote's indicator light turns on solid. Release both buttons.

If you have an original RC-799M and wish to control other components like a TV or BD/DVD player, follow these steps: Assigning a Device Code: Hold down the desired REMOTE MODE button (e.g., BD/DVD, CBL/SAT) and the

This remote is packaged with or supports several popular Onkyo AV receivers, including but not limited to: Button Layout and Essential Functions

Czy chcesz przełączyć się na wersję dla swojego kraju?

Na stronie internetowej dla swojego regionu znajdziesz informacje o produktach, które Cię dotyczą, dane kontaktowe i aktualności.

Manual High Quality: Onkyo Rc-799m Remote

Once programmed, navigating the RC-799M requires understanding its primary zones.

Turns the Onkyo AV receiver on or puts it into standby mode.

Even with a simple device like the RC-799M, problems can occasionally arise. Here are some of the most common issues and how to solve them.

If the code is accepted, the indicator light will flash twice and turn off. If it flashes once slowly, the code was incorrect, and you must restart from Step 3. onkyo rc-799m remote manual

The Onkyo RC-799M is a relatively simple device, but proper understanding is essential to fully utilize your AV receiver. Many users seek out the manual for various scenarios:

The RC-799M is a learning remote, meaning it can control your Samsung TV or Sony Blu-ray player. You do not need the original remote for the other device.

Click the battery cover securely back into place. Here are some of the most common issues

The RC-799M features a logical, zone-based button layout designed to control both your main AV receiver and connected source devices. 1. Power and Input Selection

| | Likely Cause | Solution | | :--- | :--- | :--- | | The remote does not work at all | Dead batteries | Replace the two AA batteries with fresh ones. | | | Obstruction | Ensure nothing is blocking the IR sensor on the receiver front panel. | | | Wrong polarity | Check that the + and – symbols align with the markings in the battery compartment. | | Some buttons work, but others don't | Dirt/Debris | The remote may have liquid or debris trapped under the buttons. Gently clean the exterior with a soft, dry cloth. | | | Generic limitation | If this is a replacement remote, it may not support the "Mute" button or secondary device control. Check your product listing for limitations. | | Short range (must be very close to the receiver) | Low batteries | Weak batteries reduce the infrared output. Replace them immediately. | | | IR sensor wear | Over time, the IR emitter can weaken. Try a different angle. |

Hold down the DISPLAY button and the appropriate REMOTE MODE button (e.g., TV, BD/DVD, or CBL/SAT) simultaneously for roughly 3 seconds. The remote's indicator light will light up or blink. The Onkyo RC-799M is a relatively simple device,

Make sure no physical objects are blocking the path between the remote and the receiver.

: Compact fluorescent lamps (CFLs) or bright sunlight hitting the receiver’s front display can interfere with infrared signals. Try shielding the receiver from direct light. 6. Compatible Onkyo Receiver Models

Hold both buttons for approximately 3 seconds until the remote's indicator light turns on solid. Release both buttons.

If you have an original RC-799M and wish to control other components like a TV or BD/DVD player, follow these steps: Assigning a Device Code: Hold down the desired REMOTE MODE button (e.g., BD/DVD, CBL/SAT) and the

This remote is packaged with or supports several popular Onkyo AV receivers, including but not limited to: Button Layout and Essential Functions